Please wait...

has been added to your cart!

Continue shopping
View cart & checkout
has been removed from your cart!

Continue shopping
View cart & checkout
> > > > > >
Subsalve EFB-1000 1100lb. Enclosed Flotation Bag AVAILABILITY: Normally Ships in 1-5 Business Days

BUY THIS Subsalve EFB-1000 1100lb. Enclosed Flotation Bag TODAY FROM RENTAL TOOLS ONLINE.
This versatile underwater lift bag from Subsalve(model: EFB-1000) is available at one of the best prices anywhere on the internet or in-store!


When you need to float an object close to the surface, use SUBSALVE’s “pillow” shaped Enclosed Flotation Bags in any position—upright or flat, outside or inside of structures— for vessel salvage, auto recovery, pipeline and cable installation and emergency flotation for ships, aircraft, submersibles and ROVs

Configure a multitude of rigging combinations.
  • Use with a single pick point (shackle supplied on the bottom of the bag).
  • Invert to use the multiple stainless steel rings on the top of the bag.

  • Urethane-coated nylon—high-strength and heavy-duty
  • Superior abrasion resistance
  • Resistant to most petro-chemicals
  • UV-resistant
  • Low maintenance requirements and easy to clean
  • RF welded seams

  • Lifting Harness
  • Heavy nylon lift harness built into the body of the lift bag
  • Safe working ratio of 6:1

Safe and easy of use
  • Equipped with all necessary hardware—ready for immediate use
  • 3/4” NPT inflation/deflation port
  • Stainless steel quick disconnect for inflation
  • Pressure relief valves: set to release at 2.5 psi above ambient pressure
  • Enough pressure relief vales are installed in each bag to allow expanding to vent should a free ascent occur.

• Each SUBSALVE USA lift bag is tested prior to shipping.
• Custom sizes available.
• All Subsalve USA products are compliant with IMCA D-016-AIRBAGS, ABS, U.S. Department of Defense Standards.

Additional Information

Additional Information

SKU 101235
Weight 30
Country of Manufacture United States
Mfr. Model Number EFB-1000
Link to User Manual Subsalve Lift Bag User Manual
Link to Schematics x
Link To Catalog
Technical Specifications 1/4" NPT inflation port Equipped with stainless steel quick disconnect for inflation 3/4" NPT stainless steel ball valve for deflating Pressure relief valves set to release at 2.5 psi above ambient pressure
Free Shipping No

Product Questions

Sort by ASC
Yes I have an old steel float boathouse and the back is sinking and I need to install more Styrofoam under it. But I need to lift it up. Will this work or do I need bigger ones?
Our boat recently sank due to hurricane Irma and am looking to lift it. It has sunk by the dock and the boat is totally submerged. The sailboat is 23,000lbs and I was wondering what type and how many lift bags I will need to lift the boat. Thank you for your time
I have i 50ft by 18ft pontoon boat. Weight approximately 22000 pounds. Looking to b able to lift section above waterline to do hull repairs. Can this be accomplished with your bags and if so how many would i need?
I keep my jet ski at a dock in a marina. Id like to raise it out of the water say 8 inches to mainly get the jet drive out of the water. Im thinking of sliding say your EFB-1000 bag under the hull; throw a couple a straps around the jet ski to secure to your bag. Then inflate. Would this work?
Would the bag cause the jet ski to roll over. Would the bag stay under the hull ? Remember I don't need to get say the bow area completely out of the water. Just want to mainly raise the rear of the ski up.
Jet ski weight about 1000 lb
For moving a 900 boat lift in and out of the water each season, am I better off w/ one 1000lb bag, 2x 500lb bags or another option?